The most instructive pallet I ever saw was leaning about four degrees inside a trailer, somewhere around the second hour of a delivery run. Nothing had broken. The cases were decent, the wrap was on, the pallet was sound. But the load had been built the way the operator liked building it — fast, slightly proud of the pallet edge on two sides, layers repeated identically from bottom to top — and two hours of road vibration had simply finished the argument that geometry had started at the palletizer.
Nobody had done anything reckless. They had just treated stability as a wrapping problem. It is not. Stability is a geometry problem, and the wrap only gets to vote at the end.
Two patterns, one honest trade-off
Strip away the software libraries and the pattern names, and palletizing offers two basic ways to stack a layer on the one below.
Column stacking puts every case directly on top of the case beneath it, corner on corner, edge on edge. Corrugated board carries its compression strength in its vertical walls and corners, so a column stack sends the load straight down the strongest path the material has. For weak cartons, heavy contents, or loads that will be stacked two-high in a rack, columns are how you keep the bottom layer from slowly buckling.
Interlocked stacking — the brick pattern — rotates or mirrors each layer so the cases bridge the joints of the layer below, like bricks in a wall. Now the layers are tied together. The load resists lateral movement, shrugs off the little nudges of conveyor transfers and forklift travel, and does not shed a layer when the truck brakes. The price is real, though: the weight no longer travels corner to corner, and published comparisons put the loss of stacking strength at up to around 30 percent compared with a pure column build.
So which one is "better"? Wrong question, and I say that as someone who argued the brick side for years. Weak cases with soft contents need the strength of columns and get their lateral stability from containment instead. Rigid cases that could wander in transit gain more from interlocking. Anyone who gives you a universal answer has not watched enough loads arrive.
There are refinements — pinwheel patterns for awkward footprints, split layers, a column base with interlocked upper layers as a deliberate compromise — but they are all negotiations between the same two currencies: strength downwards, grip sideways.
The overhang tax
If patterns are a negotiation, overhang is just a fine. Overhang is any part of a case extending past the edge of the pallet deck, and it is astonishingly common, because it feels free: squeeze the pattern out by a centimetre on each side and the cube utilization looks better on the spreadsheet.
It is not free. The corner of a case is its strongest point, and an unsupported corner cantilevers in the air while still carrying the stack above it. Freight and packaging studies put the loss of compression strength at roughly 20 to 40 percent for the affected cases — one widely quoted figure says even an inch of overhang can cost about a third of a carton's crush strength. I have seen the physical version of that statistic: bottom-layer cases with bulged walls and crushed corners, on loads that were "only a little bit over" the edge.
Underhang — a load smaller than the pallet — wastes space and annoys the cube counters, but structurally it is the safer sin. My rule on the floor is simple: build to the edge, never past it. If a pattern only fits with overhang, the pattern is wrong for that pallet, or the case size is wrong for the product. Fix the drawing, not the forklift driver's luck.
Height, cube and the centre of gravity
The other quiet temptation is height. Taller loads fill trailers and cut freight cost per case, which is why cube utilization shows up in so many project meetings. But every added layer raises the centre of gravity of what is, in the end, a unit load that has to survive acceleration, braking and warehouse floors that are never as flat as the drawings claim. A tall, interlocked, slightly overhung load is three compromises stacked on top of each other.
Layer discipline matters more than people expect, too. Complete each layer before starting the next. Keep the top flat — a level top layer stacks safely, wraps cleanly, and does not start life pre-leaning. Heavy and strong at the bottom, light and crushable at the top sounds too obvious to write down, until you have unloaded a mixed pallet where the sequencing software quietly put the detergent under the biscuits.
Containment cannot fix geometry
Stretch wrap is containment: it applies an inward holding force and ties the load to the pallet. Good wrapping — base locked to the pallet, consistent overlap, sensible film tension — absolutely earns its place. What it cannot do is create stacking strength, square up a column that started crooked, or hand a crushed corner its strength back. Wrap is the seatbelt, not the chassis. When a load fails in transit, I look at the pattern first, the overhang second, and the film last. That order has yet to embarrass me.
How I check a new pattern
Before a pattern goes anywhere near production, I want four answers. Does every case sit fully on the deck? Does the strength-versus-stability choice match the carton spec, or is it just the software default? Where does the centre of gravity end up at full height? And what does the bottom layer look like after the load has sat in the rack for a week — because creep is patient, and a pattern that survives the wrapper can still be dying slowly in storage.
For anyone who wants to dig deeper, I keep my running index of palletizing notes, pattern references and load-stability reading in one place — pattern discussions, carrier guides and the failure photos that teach more than the successes do.
The leaning pallet in that trailer taught the cheap version of the lesson: the load was rebuilt inside the footprint, layers interlocked against the road, wrap unchanged. It arrived straight. Geometry had not changed its mind; we had just finally agreed with it.
Top comments (0)