DEV Community

La Primera Capa
La Primera Capa

Posted on Originally published at laprimeracapa.es

A bad first layer in 3D printing: nozzle height, bed surface and how to test it

The first layer is the base everything else is built on, and Prusa calls problems with it the most common 3D printing problem and probably the first one you will meet. A first layer can stick to the bed and still be wrong: separate lines, squashed areas, differences from one zone to another, or a base wider than the rest of the part. Each defect has several possible causes, from the cleanliness of the bed to the height of the nozzle.

What a good first layer looks like

Bambu Lab describes it as smooth, uniform and well adhered, with clean lines that overlap without ridges or air gaps.

What you see What to check first
Thin, wavy or separated lines A dirty bed, and whether the nozzle is too high
Very squashed layer, raised edges or drag marks Whether the nozzle is too low; on the Bambu Lab A1, also the screws of the heater assembly
Good in some areas, bad in others Dirt in those areas, then the automatic bed calibration
No material comes out when the print starts Whether the nozzle is too low, or a clog
The base is wider than the rest of the part Z offset, bed temperature, and too much material in the first layer

Dirty bed

Fingerprint grease and other residue can keep the filament from sticking evenly. For its steel sheets, Prusa recommends isopropyl alcohol of 90% or more as the best degreaser, and notes that skin or nail products can contain additives such as moisturizers and oils. If adhesion seems to fade even with alcohol, it says you can wash the sheet with a few drops of dish soap and warm water (not too hot), though not often. It also says there is no need to clean the sheet before every print if you have not touched it with your hands.

Nozzle too high or too low

Bambu Lab's rule of thumb: if the layer barely sticks or comes out thin and wavy, the nozzle is too high. If it is so squashed that it raises edges or the nozzle drags, it is too low. That height is set by the Z offset, the position of the nozzle relative to the bed, and one cause of a wrong value is not having leveled the bed, especially after changing the plate. Bambu Lab says to level automatically first and leave manual leveling as the last resort.

Each manufacturer handles the adjustment its own way. On the MK2 and MK3, Prusa uses Live Z adjustment inside its first layer calibration. For the A1, Bambu Lab documents a temporary G-code adjustment, with values specific to that model, and says it is only a quick temporary fix: afterwards, go back to the default and focus on leveling.

If the nozzle is too low, Prusa notes that the printer may not extrude plastic for the first layer or the first two.

Screws in the toolhead (Bambu Lab A1)

On the A1, a first layer that is too low can also mean the hotend has shifted relative to the leveling. Bambu Lab's procedure: with the printer off and the hotend removed, retighten the three mounting screws of the heater assembly with an H2.0 hex key and the four small ones on the back with an H1.5.

Speed and temperature

With nozzle height checked, speed and temperature come next. Prusa suggests lowering the speed to about 75% for the first three layers. For new materials that do not stick well, it suggests raising the bed temperature by 5 to 10 °C.

Clogged nozzle

A total or partial clog can also ruin the first layer. Prusa lists it among the causes in its first layer guide.

Uneven or damaged surface

A nozzle set too low can damage the steel sheet, and some surfaces have irregularities that mesh leveling does not compensate. For that, Prusa gives a temporary fix, a sheet of paper under the uneven area of the sheet, and a more permanent one, the bed leveling correction in the firmware.

Wide base (elephant foot)

Creality defines elephant foot as a defect at the bottom of a print where the first layer or layers are wider or bulged out compared to the rest of the part. Its listed causes include a Z offset that is too low, a bed that is too hot and too much material in the first layer. Its fixes: raise the Z offset by 0.05 to 0.1 mm, lower the bed temperature in small steps (for example 5 degrees), and check the amount of material in the first layer. Cura also has "Initial Layer Horizontal Expansion", and a small negative value prints the first layer inside the boundaries of the model.

How to run a first layer test

Bambu Lab's suggestion is to print a cube 0.2 mm thick scaled to fit the bed, so that the result is a single layer. Before printing it, the page lists: wash the plate, check the nozzle and screws, run the automatic calibration, use dry filament and lower the first layer speed. A good result leaves uniform lines without gaps, a continuous surface without ridges or drag marks, and a layer without raised edges. If one area comes out worse than the others, clean the plate and repeat the automatic leveling before turning to manual.

What not to do

Prusa warns against compensating for poor adhesion with a lower Live Z value, squashing the first layer: go too low and the nozzle can damage the steel sheet. It also says not to put super glue on the sheet and never to use acetone on textured or satin powder-coated sheets.

Sources

Everything above comes from the manufacturers' own documentation:

  • Prusa, "First layer issues", Prusa Knowledge Base (consulted 04/11/2026, read again 11/11/2026 in its Spanish version).
  • Bambu Lab, "Identify and fix first layer issues with a test print", Bambu Lab Wiki (consulted 04/11/2026).
  • Bambu Lab, "Print issues troubleshooting" for the A1 mini, section "First layer too low", Bambu Lab Wiki (consulted 04/11/2026).
  • Creality, "3D Printer Elephant Foot", Creality blog (consulted 04/11/2026).

The full version, in Spanish and with compatible parts for specific printers, is at laprimeracapa.es.

Top comments (0)